Coil Winding Machine

Because it is difficult to wind cylindrical coils with a neat winding pattern and a high copper fill factor without the proper equipment, the idea arose to automate this process. The biggest challenge here was being able to wind coils with different geometries and wire cross-sections while maintaining consistent quality.

10/01/2024 - 03/14/2025

Coil Winding Machine for the Production of Cylindrical Coils for Prototype Development

Degree Program

ET - Discontinued

Project Description

Due to the difficulty of winding cylindrical coils with a neat winding pattern and a high copper fill factor without a suitable device, the idea arose to automate this process. The biggest challenge here was to be able to wind coils of different geometries and wire cross-sections with consistent quality.

This project focuses on the development of a device for manufacturing small and medium-sized cylindrical coils for prototyping.
The winding process was to be automated as much as possible.
To achieve this, an intuitive menu was programmed that can be controlled via an incremental encoder.

After entering the following parameters, the required wire length is first calculated and displayed on the screen.

Coil parameters:

  • Effective coil length
  • Coil body diameter
  • Wire diameter
  • Number of turns

The starting position of the linear guide can then be set by turning the incremental encoder.

Based on these parameters, the feed rate and the position for the direction reversal at the end of the coil are now determined. During the winding process, the current number of turns is shown on the display. By turning the incremental encoder, the winding speed can now be adjusted continuously. It is also possible to pause and resume winding during the process.
One of the challenges here was maintaining constant wire tension throughout the winding process.

People Involved

Student group: Niklas Bauer, Bernd Gürtner

Advisor: Prof. Dr.-Ing. Wolfgang Meyer

Course

Systems Engineering 1 (IK)

Duration

Winter Semester 2024/25

Requirements

  • Automation of the winding process
  • Maintaining an acceptable winding time
  • Maximum dimensions: 70 mm winding length, 50 mm winding diameter
  • Capable of winding wire cross-sections up to 1 mm²
  • Ability to pause and resume the winding process
  • Intuitive input of winding parameters
  • Overload protection without damaging the machine
  • Calculation and display of the required wire length
  • Continuously adjustable winding speed during operation
  • 230 VAC power supply

Implementation

First, a conceptual design was developed to meet the requirements mentioned above. Based on this, the components to be used were selected.
A wooden screen printing frame was chosen as the base frame because it is sturdy, easy to work with, and fits within the budget.

The two shafts are made of steel, and the spool holders and idler pulleys are made of brass.
After finalizing all components and materials, a CAD drawing of the system was created, and the mechanical assemblies were manufactured based on that drawing.

Stepper motors were used for the drives because they offer high positional accuracy, eliminating the need for an additional sensor for position detection.
To ensure sufficient torque for larger wire cross-sections and winding diameters, the main drive can be operated via a gearbox in reverse, which increases the torque tenfold.

The wire brake consists of a cable connected at one end to the base plate and wound around the shaft at the other end.
The friction—and thus the braking effect—can be adjusted by varying the number of turns and the cable’s pretension.

Control is provided by an incremental encoder with a push-button function, which is connected to an STM32 microcontroller with appropriate debouncing.
This microcontroller controls the two drives via a high-performance stepper driver expansion board and displays the corresponding information on the LCD screen.
The electronics are powered by a 12 VDC power supply with a maximum output current of 3 A.

Uses

The machine was developed primarily for use in prototyping. It enables the production of cylindrical coils that can be used in a variety of applications. These include:

  • Electromagnets
  • Filter circuits
  • Energy storage in power electronics
  • Inductive proximity sensors

The coil forms can, for example, be manufactured using a 3D printer and, if necessary, equipped with an iron core to improve their magnetic properties.
The coil shape does not necessarily have to be round. By adjusting the geometry of the coil mounts, square or rectangular coil bodies can also be accommodated.

Other Projects at THA

A man wearing a helmet and carrying a leather shoulder bag is riding a bicycle

07/01/2026 - 06/30/2029

A2W

Active to Work - Active Commuting: Effects on Mental Health and the Role of Urban Environmental Factors

Discover project
Students wearing VR headsets

04/01/2026 - 04/30/2029

Gesellschaft • KI

AI-Supported, VR-Based German Language Learning for Future Professionals

The project “AI-Supported, VR-Based Skills Competition for Future Professionals in the Field of German as a Technical and Professional Language” addresses the ongoing shortage of skilled workers

Discover project

02/01/2026 - 01/31/2027

GeWo-Bay Study

An exploratory field study is examining health care for homeless people in Bavaria.

Discover project

02/01/2026 - 01/31/2029

Digitalisierung • Robotik

BOSDra

BOSDra is developing an automated first-response drone system for law enforcement and other organizations with security responsibilities (BOS).

Discover project
Ambulance Image

01/01/2026 - 12/31/2027

WARM Study

Effects of Environmental Factors on Acute and Chronic Wounds, Mental Health Conditions, and Social Factors Among People Experiencing Housing Crises in Augsburg

Discover project
Two field workers use an app on a construction site to install fiber-optic cables

01/01/2026 - 06/30/2027

Digitalisierung

DocPilot

Digital Data Management for Fiber-Optic Network Expansion

Discover project

01/01/2025 - 12/31/2026

Ressourceneffizienz • Wasser

Cost-Effective Upgrades to Wastewater Treatment Plants

Cost-Effective Upgrading of Wastewater Treatment Plants by Improving the Settling Properties of Activated Sludge

Discover project
Cover photo: DiPukS

08/01/2024 - 06/30/2027

Digitalisierung

DiPukS

Digital Planning Support for Climate-Neutral Urban Development

Discover project